Quality

Pre-shipment inspections and AQL: how to book one that answers your questions

How to brief a pre-shipment inspection, understand AQL sampling and assess the findings behind an overall pass or fail result.

By Packsel Consulting, Purchasing insights
Article date: · 5 min read
Updated:

A pre-shipment inspection needs a clear brief. A product name and factory address provide little guidance on the dimensions, functions or packaging requirements that matter to your business. Defining those criteria before the visit makes the inspection report more useful for the shipment decision.

Preparation is the starting point: agree what the inspection needs to establish and provide the references required to assess it.

Confirm the goods are really ready

A pre-shipment inspection is meant to happen when production is finished and at least 80 percent of the order is packed. Ask the factory to confirm, in writing, how many units are finished and how many are in cartons. If readiness is unclear, resolve the quantities and packing status before confirming the visit.

Partly finished goods can still be inspected, but that is a during-production check. It answers a different question and should be booked as one.

Also leave time after the inspection. Allow sufficient time between inspection and loading to assess findings and arrange any corrective work.

Send the inspector a reference, not a description

The inspector needs to know what “right” looks like. That usually means:

  • the current specification and drawings, with the revision date
  • photos of the approved sample, or the sealed sample itself
  • the purchase order quantities by SKU and colour
  • packaging and labelling artwork
  • the functions to test and how to test them
Area What to send beforehand Expected inspection record
Quantity PO quantities by SKU Units found, units packed, cartons opened
Appearance Approved sample, defect definitions Defects found, with photos and classification
Dimensions Critical measurements and tolerances Measured values and the tool used
Function Test steps and the expected result What was done, under what conditions, and the result
Packaging Artwork, carton marks, drop-test requirement Findings against the artwork and carton spec

If you don’t yet have a tolerance for something, don’t invent one to fill the table. Note it as a gap and decide who sets it.

What AQL means, and what it doesn’t

AQL inspections draw a random sample from the lot and count defects in it. The sample size comes from a table in ISO 2859-1, or its U.S. equivalent ANSI/ASQ Z1.4, based on the lot size and an inspection level. General Inspection Level II is the usual default.

You then set an acceptance limit for each class of defect. A common starting point for consumer goods is 0 for critical defects, 2.5 for major and 4.0 for minor. The table turns those into numbers: for a lot of 3,000 units at Level II, the inspector checks 125 units, and the order fails on major defects if 8 or more are found.

ASQ’s overview of the sampling standards is a good primer. Two things trip buyers up:

  1. An AQL of 2.5 does not mean the shipment has 2.5 percent defects. It describes the sampling plan’s behaviour over many lots, not the quality of this one.
  2. A pass on the sample is a statement about the sample. It is not a guarantee that no defective unit got through.

Keep inspection and testing apart

An inspector can check appearance, count, measure and run simple function tests. A lab tests things like material composition, flammability or electrical safety under controlled conditions.

For each test on your list, decide whether the inspector will perform it, watch the factory perform it, or whether it goes to a lab. Write that down. If the product is regulated, the lab report is what counts, and an inspection report shouldn’t be passed off as certification.

Review the findings and exceptions

Look past the overall result. A report can pass on AQL and still flag a problem you care about, such as a carton mark error that will cause trouble at your warehouse.

Review any checks that were not completed. “Not tested, no power supply available” is not the same as “tested, passed.” These exceptions may appear in the report notes rather than the overall result.

Assign acceptance and follow-up authority

Before inspection, identify who can approve a deviation, request rework or authorize reinspection, and define the evidence the factory must provide afterward. A missing manual might mean repacking and a quick recheck of those cartons. A failed electrical test needs a much more careful response.

How we prepare for a pre-shipment inspection

Before we book an inspection, we ask the factory how many units are finished and how many are packed, and we confirm the date only when at least most of the order is in cartons. We send our inspector the specification, approved sample photos, quantities and the test list, and we agree with the client in advance what happens on a failure. On site, our inspector picks cartons at random from across the stack, not just the front row, and records every finding with a photo and carton number.

Packsel Consulting carries out on-site inspections against an agreed checklist, as a one-off or alongside production follow-up and shipping coordination.

About these articles

Packsel Consulting

Purchasing insights · U.S. and Hong Kong

Practical guidance for U.S. businesses buying from Asia.

How we work
More insights

Get in touch

Tell us what you’re buying.

Send us the product, the supplier if you have one, and your dates. We’ll suggest a scope for one stage or the whole order.